MTP/MPO Array Cable for 400G & 800G Data Centers | EXW
EXW provides pre-terminated MTP/MPO array cables for 10G to 800G data center networks. Available in 12F, 16F, 24F and 32F with OM3, OM4, OM5 and OS2 fiber, multiple polarity options, and Standard, Low or Ultra Low Loss performance.
MTPĀ®/MPO Array Cable
Pre-Terminated MTPĀ®/MPO Array Cable for 400G and 800G Data Center Links
Every array cable is factory-terminated and individually tested before shipment, so link loss is documented before installation rather than discovered during commissioning. Polarity is specified at order ā Type A, B, C or customized ā and the same cabling architecture carries you from 10G through 800G without re-pulling fiber.
Specifications
- Connector fiber counts: 12F, 16F, 24F and 32F. Cable assemblies are available populated with 8 or 12 fibers.
- Fiber types: OM3, OM4, OM5 (BIMMF) and OS2 G.657.A single mode.
- Network speeds: 10G / 40G / 100G / 200G / 400G / 800G. See the configuration table below for which fiber count applies to each application.
- MTPĀ® OM4 APC assemblies support 400GBASE-SR8, compatible with OSFP and QSFP-DD transceiver modules.
- Connector options: US Conec MTPĀ® Elite or MPO-compatible. End-face polish: APC for single mode and for MPO-16 parallel-optics applications; UPC for standard multimode.
- Performance grades: Standard Loss, Low Loss and Ultra Low Loss ā see the insertion loss table.
- Polarity: Type A, B, C, and customized.
- Connector types: male (with pins) and female (unpinned).
- Cable jacket: LSFRZH or PVC. Flame rating: built with UL-Listed OFNR (riser) or OFNP (plenum) rated optical fiber cable, per UL 1651. Listing documentation available upon request.
- Connector interfaces conform to the IEC 61754-7 series: 12F to IEC 61754-7-1 (one fibre row), 16F to IEC 61754-7-4 (one fibre row, 16 fibres wide), 24F to IEC 61754-7-2 (two fibre rows), and 32F to IEC 61754-7-3 (two fibre rows, 16 fibres wide).
- Further assemblies, fanout length and cable length available on request.
Mechanical Characteristics
- Reliable high-density interconnection for : Data communications networks, including high-bandwidth equipment, interconnections for parallel optical transmitters and receivers, telecommunications networks and broadband/CATV networks.
Note
- Fiber Compatibility: OM3, OM4, OM5 (BIMMF) and OS2 G.657.A
- Available in 12, 16, 24 and 32 fiber connector counts with OM3, OM4, OM5 and OS2 G.657.A, supporting network speeds from 10G to 800G. Cable assemblies can be populated with 8 or 12 fibers depending on the application.
Cable Outer Diameter by Fiber Count
MTPĀ®/MPO array cables with 8 or 12 fibers are supplied in 2.0 mm and 3.0 mm outer diameters. 16-fiber cables use a 3.0 mm outer diameter, while 24-fiber and 32-fiber cables use a 3.5 mm outer diameter.
| Cable fiber count | 2.0 mm | 3.0 mm | 3.5 mm |
|---|---|---|---|
| 8F / 12F | Available | Available | Not available |
| 16F | Not available | Available | Not available |
| 24F / 32F | Not available | Not available | Available |
MTPĀ®/MPO Insertion Loss and Return Loss Grades
Maximum insertion loss per MTPĀ®/MPO connector mating. Multimode BIMMF OM3/OM4/OM5 assemblies are rated at 0.50 dB (Standard Loss), 0.35 dB (Low Loss) and 0.25 dB (Ultra Low Loss). Single-mode OS2 G.657.A assemblies are rated at 0.75 dB (Standard Loss), 0.35 dB (Low Loss) and 0.25 dB (Ultra Low Loss). Return loss is specified per grade in the same table.
| Grade / Fiber Type | Standard Loss | Low Loss | Ultra Low Loss |
|---|---|---|---|
| Insertion loss ā BIMMF OM3 / OM4 / OM5 (Multimode) | ≤ 0.50 dB | ≤ 0.35 dB | ≤ 0.25 dB |
| Insertion loss ā SM OS2 G.657.A (Single-mode) | ≤ 0.75 dB | ≤ 0.35 dB | ≤ 0.25 dB |
| Return loss ā BIMMF OM3 / OM4 / OM5 (Multimode) | ≥ 20 dB | ≥ 25 dB | ≥ 25 dB |
| Return loss ā SM OS2 G.657.A (Single-mode) | ≥ 60 dB | ≥ 60 dB | ≥ 60 dB |
Which Configuration for Which Application
The table below maps the parallel-optics Ethernet interfaces to the fiber count, connector interface and polarity they require. Standard channel reach is given for OM3 and OM4; OM5 performs equal to or better than OM4 at 850 nm.
| Ethernet Interface | Typical Transceiver | Fiber Type | Active Fibers | Connector Interface | Polarity / Lane Mapping | Standard Channel Reach |
|---|---|---|---|---|---|---|
| 40GBASE-SR4 | QSFP+ | OM3 / OM4 / OM5 | 8 | MPO-12, 8 positions populated | Type B commonly used; confirm system architecture | OM3: 100 m OM4 / OM5: 150 m |
| 100GBASE-SR4 | QSFP28 | OM3 / OM4 / OM5 | 8 | MPO-12, 8 positions populated | Type B commonly used; confirm system architecture | OM3: 70 m OM4 / OM5: 100 m |
| 400GBASE-SR8 | QSFP-DD / OSFP | OM3 / OM4 / OM5 | 16 | MPO-16, or 2 × MPO-12, or MPO-24 with 16 positions populated; APC or UPC per transceiver | Confirm MDI and lane mapping | OM3: 70 m OM4: 100 m (OM5 equal or better) |
| 800GBASE-SR8 | OSFP / QSFP-DD | OM3 / OM4 / OM5 | 16 | MPO-16 APC, 2 × MPO-12, or MPO-24 UPC, depending on transceiver | Confirm MDI and lane mapping | OM3: 60 m OM4: 100 m (OM5 equal or better) |
24F and 32F assemblies are used primarily for high-density trunk and backbone cabling. Direct connection to a transceiver is a specific application, seen in less common parallel-optics standards such as 100GBASE-SR10 and 400GBASE-SR16. For any configuration not listed, confirm compatibility against the transceiver interface, fiber count and link-loss budget with our engineering team.
How to Order an MTPĀ®/MPO Array Cable
Each MTPĀ®/MPO array cable is built to order. Specify the following eight parameters when requesting a quotation so the assembly arrives ready to install without field adaptation.
| Step | Parameter | Options |
|---|---|---|
| 1 | Number of connector cores | 12F / 16F / 24F / 32F |
| 2 | Fiber mode | Single mode: G.657.A1 / A2 (yellow). Multimode: OM3 (aqua), OM4 (violet), OM5 (lime green). |
| 3 | Connector option | US Conec MTP® Elite or MPO-compatible |
| 4 | Connector type | Male (with pins) / Female (unpinned) |
| 5 | Polarity | Type A / Type B / Type C / Customized |
| 6 | End-face / Polish | Single mode: APC. Multimode: UPC, or APC for MPO-16 parallel optics. Performance grade: Standard Loss / Low Loss / Ultra Low Loss. |
| 7 | Cable jacket and flame rating | Jacket: LSFRZH or PVC. Flame rating: UL-Listed OFNR (riser) or OFNP (plenum). |
| 8 | Length | Feet / Meters |
MTP® and Elite® are registered trademarks of US Conec Ltd.
- Related Products
Fiber Optic Simplex / Duplex Pigtail Patch Cord
001 series are manufactured strictly according to international standard. Pigtail is a fiber...
Details Add to List
Fiber Optic Mini Breakout Cable
002 mini break out cable is the very compact and space saving cable distributor because the cable...
Details Add to List
MTPĀ® / MPO Trunk Cable
004 cable assemblies allow for a rapid deployment of high density permanent links in a single...
Details Add to List
Harness Fiber Patch Cable
006 harness series is for transition from trunk backbone assemblies to fiber rack system. MTPĀ®/MPO...
Details Add to List
Fiber Optic MTPĀ® / MPO to LC / SC Harness
005 direct harness has a pinned (male) MTPĀ®/MPO connector on one end and while the other end is equipped...
Details Add to List- FAQ
Category 8 Solutions for Future Networks
Category 8 RJ45 solutions are designed to support Ethernet at rate up to 40 Gbps (40GBASE-T) for short distances up to 30 meters, which is a solution primarily...
All of EXW Patch Cords Use Bare Copper Wires
All of EXW patch cords use pure bare copper wires. EXW patch cords do not use CCA (copper clad aluminum) wires nor do we recommend using patch cords made...
- Files Download
Array Cord 24C MTP(F) to MTP(F) B Type
Pre-terminated MTPĀ®/MPO array cables, 12Fā32F, 10G through 800G
Download
Download Best-Selling
How can MTP/MPO Array Cable support your network infrastructure requirements?
EXW provides pre-terminated MTPĀ®/MPO array cables for high-density fiber optic connections in data centers, telecommunications networks, broadband networks, and parallel-optics applications. Available in 12F, 16F, 24F, and 32F connector configurations with OM3, OM4, OM5, and OS2 G.657.A fiber, these assemblies support network speeds from 10G through 800G. Each cable is factory-terminated and individually tested before shipment, helping network installers verify link performance before deployment.
MTPĀ®/MPO array cables can be configured with Type A, Type B, Type C, or customized polarity, male or female connectors, and Standard Loss, Low Loss, or Ultra Low Loss performance grades. MTPĀ® OM4 APC assemblies support high-speed parallel-optics applications such as 400GBASE-SR8 and 800GBASE-SR8 with MPO-16 connectivity for OSFP and QSFP-DD transceiver modules. Cable jacket, fiber mode, connector type, polarity, performance grade, fanout length, and overall cable length can be specified according to project requirements.